Product Overview — EP-S47 Helical-Worm Gear Reducer
Food processing, pharmaceutical production, and precision packaging demand a right-angle gear reducer that maintains repeatable speed, tolerates frequent washdown, and generates minimal heat in production spaces where temperature control matters. The EP-S47 helical-worm gear reducer is engineered for exactly this environment — delivering up to 270 N·m output torque from 0.12–2.2 kW across ratios of 8.74–196.11, with an overall efficiency of 75–82% that significantly reduces heat output compared with conventional worm reducers.
The two-stage gear architecture — helical input, worm output — is optimally suited to duty cycles with moderate shock loading and frequent start-stop. The helical stage absorbs most of the speed reduction at high efficiency, leaving the worm stage to deliver the final ratio at low sliding velocity. This reduces the surface temperature of the worm gear set relative to a single-stage design, extending lubricant life and minimising the frequency of thermal-degradation-driven oil changes.
Stainless-steel fasteners, Viton lip seals, and NSF-approved food-grade synthetic lubricant are available as a washdown-service option pack. The smooth housing exterior has no unnecessary projections that trap contaminants, and the paint system is resistant to common cleaning agents. Our application engineers can advise on seal selection for pressurised or steam-clean environments.
Technical Specifications — EP-S47
| Parameter | Specification |
|---|---|
| Gear Type | Helical pre-stage + worm gear set (right-angle output) |
| Number of Stages | 2 (1 helical + 1 worm) |
| Motor Power Range | 0.12–2.2 kW |
| Max Output Torque | 270 N·m |
| Gear Ratio Range | 8.74–196.11 |
| Output Speed Range | 7–161 rpm |
| Approximate Unit Weight | 9–14 kg |
| Max Output Radial Load | 3,800 N |
| Overall Efficiency | 75–82% (vs 55–65% for equivalent single-stage worm) |
| Lubrication | Oil bath; ISO VG 220 synthetic-blend worm gear oil (factory fill) |
| Housing Material | Close-grained cast iron (HT250) |
| Worm Shaft Material | 20CrMnTi alloy steel, case-hardened HRC 58–62, profile ground Ra ≤ 0.4 µm |
| Worm Wheel Material | Centrifugally cast phosphor-bronze (ZCuSn10P1) |
| Helical Stage Material | 20CrMnTi alloy steel, case-hardened, precision ground DIN 6 |
| Protection Rating | IP55 standard; IP65 optional |
| Ambient Temperature | −25 °C to +40 °C (standard lubricant) |
| Noise Level | ≤ 68 dB(A) at rated load (1 m, free-field) |
| Standards Compliance | ISO 14521 worm gear rating; ISO 281 bearing life; CE Machinery Directive |
Structural Types & Mounting Configurations — S47 Series
The S47 series is produced in five structural types plus an input-shaft-only SA-SZ variant. All share the same internal helical-worm gear train and achieve identical output torque and efficiency ratings. The structural type determines the mounting method and driven-machine interface.
| Type Code | Description |
|---|---|
| S47 | foot-mounted, solid output shaft |
| SF47 | B5 flange-mounted, solid output shaft |
| SA47 | shaft-mounted, hollow output bore |
| SAF47 | B5 flange + hollow output bore |
| SAT47 | torque-arm, hollow output bore |
SF and SAF Mounting Positions
Flange-mounted SF47 and SAF47 variants support all six standard mounting positions. Oil fill level and breather plug position must be adjusted per mounting position — refer to the position-specific lubrication table in the installation manual.
SA and SAT Torque-Arm Mounting Positions
The SA47 shaft-mounted and SAT47 torque-arm variants mount directly onto the driven shaft, reacting torque through the torque arm rather than a baseplate. This eliminates shaft-to-shaft coupling alignment and is particularly suited to conveyor head drives and drum agitators.
Key Advantages of the EP-S47 Helical-Worm Reducer
The helical input stage of the EP-S47 achieves ≥98% per-stage efficiency, contributing directly to the 75–82% overall efficiency of the complete unit — 15–25 percentage points above conventional single-stage worm reducers. In continuous-duty applications this margin translates to measurable energy cost reduction and lower operating heat, reducing cooling requirements and extending lubricant life.
The S-series right-angle configuration delivers 270 N·m from a housing sized for 0.12–2.2 kW — a torque density comparable to much larger parallel-shaft units. The perpendicular input-to-output layout is inherently suited to machine geometries where the motor and driven shaft cannot share the same axis, eliminating additional bevel stages or chain-and-sprocket drives that add cost and maintenance.
By pre-reducing speed in the helical stage before it reaches the worm mesh, the EP-S47 reduces worm sliding velocity at any given overall ratio. Lower sliding velocity directly reduces worm-mesh friction noise, yielding typical noise levels 6–10 dB(A) below equivalent single-stage worm reducers — an advantage valued in food production halls, pharmaceutical facilities, and any environment with operator occupancy near the drive.
Ratios from 8.74 to 196.11 in a single housing are achievable with the EP-S47, covering applications from moderately fast conveyor drives at the lower end to very slow-rotation stirring and positioning drives at the upper end. This breadth eliminates the need to cascade multiple reducers in most applications, simplifying the drivetrain and reducing total installation length.
Five structural types — S, SF, SA, SAF, SAT — plus the SA-SZ input shaft variant address every practical machine interface without custom engineering. SA and SAF hollow-bore types allow direct shaft mounting, eliminating flexible couplings and their associated alignment requirements. The SAT torque-arm type simplifies drum and conveyor installations further by reacting torque through a single rubber-buffered arm rather than a rigid baseplate.
The EP-S47 worm wheel is manufactured from centrifugally cast phosphor-bronze (ZCuSn10P1), chosen for its combination of high load capacity, low friction against hardened steel, and resistance to adhesive wear under boundary-lubrication conditions during start-up. The hardened and profile-ground worm shaft (Ra ≤ 0.4 µm) maintains an elastohydrodynamic oil film across the full operating speed range, extending tooth-surface life to typically 25,000–40,000 hours.
Structural Type Diagrams — S47 Series
Use the diagrams below to confirm the external geometry, mounting interface, and connection dimensions of each S47 structural type before finalising your machine design. Certified dimensional drawings in DXF and PDF are available on request.
S47 Foot-Mount, Solid Output Shaft
SF47 B5 Flange, Solid Output Shaft
SA47 Shaft-Mounted, Hollow Bore
SAF47 B5 Flange + Hollow Bore
SAT47 Torque-Arm, Hollow Bore
SA47-SZ Input Shaft Only
Industry Applications — Where the EP-S47 Excels
| Industry Sector | Typical Application |
|---|---|
| Ink fountain drives, foil-stamping unit feeds, and web-tension dancers on commercial printing presses. | |
| Filling nozzle indexing, label applicator drives, and capping machine torque heads in bottling plants. | |
| Pharmacy Production | Tablet coating pan drives and blister-feeder index units where validated quiet operation is a regulatory expectation. |
| Small Conveyors | Checkout belt drives, postal-sorting induction feeds, and small-parts accumulation lines. |
Application Case Study: Bottling Line Capping Torque Control
A soft-drink bottler replaced worn worm-only reducers on 12 capping heads with EP-S47 helical-worm units. The helical input stage raised efficiency from 62% to 79%, reducing heat in the cap-torque-sensing circuit that was causing nuisance torque-trip alarms. After 14 months of three-shift operation, zero torque alarms attributable to drive overheating have been recorded.
Model Designation Guide — How to Order an EP-S47
Every element of the S-series order code defines a specific product attribute. The example below shows a 1.5 kW, torque-arm, hollow-bore unit in mounting position M1:
EP – S47 – SAT – Y – 2 – 1.5 – 4P – M1
| Code Element | Meaning |
|---|---|
| EP | Brand identifier — Ever Power |
| S47 | Series and frame size — S-series helical-worm |
| SAT | Structural type: torque-arm, hollow-bore output |
| Y | Motor type: Y-series IEC standard induction motor |
| 2 | Number of gear stages (helical + worm) |
| 1.5 | Motor rated power in kW |
| 4P | Motor pole count (1,450 rpm at 50 Hz) |
| M1 | Mounting position (1 of 6 standard positions) |
Frequently Asked Questions — EP-S47
How does the EP-S47 compare with a pure worm reducer of the same frame size?
The EP-S47 helical-worm design achieves 75–82% overall efficiency compared with 55–70% for a typical single-stage worm reducer. In continuous-duty applications this reduces operating heat, lowers motor input power requirements, and extends lubricant life. The initial unit price is modestly higher, but the energy saving and reduced heat-related maintenance typically yield a positive ROI within 12–18 months.
Is the EP-S47 suitable for washdown environments in food production?
Yes. An optional stainless-steel fastener and Viton shaft-seal pack upgrades the EP-S47 for IP65 washdown service. Specify NSF-approved synthetic food-grade lubricant when ordering for food-contact zones. The standard housing paint passes mild acid and alkali splash testing; for continuous wet environments an epoxy-polyurethane coating is available.
Can the EP-S47 operate in both directions of rotation?
Yes. Unlike some worm reducers, the EP-S47 is self-locking only at ratios above approximately 60:1 when loaded by the output shaft. Confirm the self-locking ratio requirement at time of order if back-driving prevention is needed for your application. For ratios below 60:1, specify an add-on backstop if uncontrolled back-driving would be hazardous.
What ordering quantities and lead times apply to the EP-S47?
1–5 sample units are accepted for engineering evaluation. Mixed-model orders are welcome from a minimum transaction value of USD 1,500. Standard configurations ship in 10–25 working days; custom specifications (special bore diameters, colour coding, ATEX) require 20–45 working days. Contact us via the inquiry page for project-volume pricing and consignment-stock arrangements.
What is the thermal power rating of the EP-S47?
The thermal power limit (P1th) for the EP-S47 at 50 Hz and 20 °C ambient is listed in our published data tables and is higher than for equivalent worm-only units because the helical stage dissipates less heat per kW transmitted. For ambient temperatures above 30 °C or for enclosed, poorly ventilated installations, use the ambient derating chart in the installation manual or contact our application team.
Upgrade Your Production Drive with EP-S47 Efficiency
Switching from a worm-only reducer to the EP-S47 helical-worm design is one of the most cost-effective energy-efficiency improvements available for continuous-duty drives. To quantify the saving for your specific duty cycle, send us your motor nameplate data and duty-cycle details via the inquiry form — we will calculate the annual energy and maintenance saving free of charge.