EP-CHG75E 75mm Paver Conveyor Chain

A 75mm-pitch scraper conveyor chain with a 32mm roller and defined attachment geometry. Built around accurate repair identification, not approximate pitch substitution.

MOQ: flexible. Minimum order value USD 1,500; mixed orders and trial quantities available.

Overview

EP-CHG75E serves a specific dimensional requirement rather than a broad interchangeable chain standard. The published specification has a 75mm pitch with a 32mm roller diameter and 15.9mm pin. A machine owner may recognize the roller and pin measurements from an old part but still need to establish whether the original pitch was 75mm. That final check is essential before ordering a chain for an existing conveyor drive.

Representative paver conveyor chain product photograph for the EP-CHG75E series; exact configuration must be checked against model dimensions
Reference paver conveyor chain photograph; the ordered CHG75E assembly must follow its specific 75 mm dimensions.

The catalogue shows a clear inner width of 32.3mm, scraper offset A3 of 56.5mm and plate height H of 38.1mm. These figures provide a useful technical starting point for the maintenance team, particularly when an old conveyor is partly dismantled and the machine build information is incomplete. Final acceptance depends on the installed sprockets and scraper hardware, not on the model title alone.

Pitch

75 mm

Roller

32 mm

Full Technical Specifications

Complete model dimensions

EP Model Pitch P (mm) Roller d1 (mm) Pin d2 (mm) Inner width b1 (mm) Scraper* Offset A3 (mm) Inner plate b2 (mm) Outer plate b3 (mm) Outer plate b4 (mm) Plate height H (mm)
EP-CHG75E 75 32 15.9 32.3 6-8 56.5 8 8 8 38.1
75mm paver conveyor chain engineering dimensional drawing for the EP-CHG75E family
Engineering profile showing the chain geometry and dimension symbols used to identify the listed EP family.

The source lists Scraper = 6-8; its precise assembly significance should be established during the quotation drawing review.

75mm paver conveyor chain specification table showing the published EP model dimensions
Series specification graphic for checking the tabulated technical values.

Related Chain Selection

An equipment review may involve a nearby nominal series; the related industrial chain range.

Reading The 75mm Drawing

Begin at the pitch line in the engineering view, which identifies successive pin centers. Then locate the roller diameter d1 and pin diameter d2. The b1 dimension identifies space between inner plates; do not confuse this with the outside width at the protruding pin heads. For the scraper connection, locate A3 and the three plate values b2, b3 and b4, all shown as 8mm for this configuration.

The technical image is a dimensional reference, not a record of an approved machine fit. When annotating an order drawing, keep the original dimension symbols so the supplier and buyer discuss the same features. If attachment holes, fastening pieces or scraper bars are omitted from the published drawing, obtain those details from the machine or from a separate approved manufacturing drawing.

Why Similar Chains Differ

An important neighboring item is the 78mm EP-CHG78E. It shares the listed 32mm roller, 15.9mm pin, 32.3mm inner width, 56.5mm offset and 38.1mm height. Nevertheless, its pitch is 78mm, not 75mm, and the printed Scraper entry is also different. This makes the pair a useful cautionary example: several matching dimensions do not erase one decisive incompatible dimension.

For a 75mm chain, sprocket engagement repeats every link. The difference between a 75mm and a 78mm pitch accumulates along the chain wrap, so visual similarity of the plates is not enough to claim replacement. A proposal to change from one family to another must include a separate assessment of the sprockets, chain route and attachment arrangement.

EP-CHG75E is defined by its complete geometry. The shared roller and pin dimensions of a nearby series cannot make a 78mm pitch into a 75mm fit.

Conveyor Handling Context

The product belongs in the scraper conveyor mechanism of a road paving machine. Material can collect near the attachment connection or between moving components, which makes clearance and access important considerations during inspection. Examine the path used by the attachment through the loaded section and the return. Distinguish genuine wear at the link surfaces from damage caused by repeated contact with fixed structures.

A service order should identify the location of the conveyor assembly in the machine and whether the replacement is a single segment or a complete run. This description matters because the technical dimensions do not state the total number of links, the attachment count for a particular machine or the joint arrangement. Those values must come from the buyer drawing or a verified sample.

Assessing The Old Assembly

First mark the direction of travel and the attachment orientation before the chain is removed. Then choose a section with minimal distortion for measuring. Check for pin rocking, roller seizure and uneven link motion. If possible, photograph the installed sprocket beside a scale and retain the previous chain arrangement as a reference for reassembly.

When describing wear, avoid assigning a universal allowable elongation percentage to this specific chain. The provided material does not publish such a limit. A mechanic can still record the measured extension and the pattern of damage to support an engineering review. This is more reliable than an unsupported statement that a certain number of operating hours guarantees a replacement interval.

When a former repair changed the drive teeth, compare the 75mm chain against sprocket constructions; verify the tooth geometry and local mounting arrangement from the actual machine rather than assuming a catalogue match.

Specification Confirmation Workflow

Ask the maintenance team to confirm pitch first, then the 32mm and 15.9mm roller/pin combination, then b1, A3 and H. Add the original chain mark, if legible, and the required quantity. If other machine components have been changed, explicitly note that history because it can affect replacement compatibility.

Ever Power can use the completed dimensional record to discuss the listed EP-CHG75E configuration or a drawing-led supply. The final scope should say whether the order includes chain only or any scraper-related elements. Avoid interpreting the catalogue family entry as proof of bundled accessories that are not specifically described in the agreed quotation.

EP-CHG75E individual technical model card
Individual model card covering the chain dimensions for EP-CHG75E.

Measurement And RFQ Sequence

  1. Write down the installed chain pitch before loosening the last connected segment.
  2. Confirm the nominal 32mm roller and 15.9mm pin on the cleanest available link.
  3. Measure the inner gap and the relative scraper offset without bending an attachment into position.
  4. Compare the figures with the EP-CHG75E drawing and keep EP-CHG78E separate despite its similar dimensions.
  5. Specify full chain length, joint configuration and whether matching scraper fittings are in scope.

Inspection Priorities

  • Inspect contact marks on the scraper where it passes the conveyor bed.
  • Check for rollers that remain stationary while the chain articulates.
  • Confirm no alternate 78mm replacement was installed during an earlier repair.
  • Photograph the chain while it is still aligned with the drive for later comparison.

Frequently Asked Questions

Why cannot I use a visually identical 78mm chain?

The pitch is different even though several other EP-CHG75E and EP-CHG78E figures coincide. Sprocket engagement and cumulative link spacing must be right along the entire chain path.

What is the pin diameter for EP-CHG75E?

The listed pin diameter d2 is 15.9mm. Check it together with P = 75mm, d1 = 32mm, b1 = 32.3mm, A3 = 56.5mm and H = 38.1mm when identifying the installed assembly.

Does the published table define an assembly length?

No complete machine-specific chain length or link count is given. Buyers should provide the installed link count, required number of runs and any special joining or scraper attachment arrangement.

Can I test this configuration with a small quantity?

Trial supply can be reviewed according to product type and order amount. Suitable first orders may involve 1-5 sample pieces; 1-2 pieces may be possible at a higher unit price. Mixed models can contribute to an approximate USD 1,500 minimum order value.

What timing and Incoterms are available?

Standard parts are normally planned at 10-25 working days, custom components at 20-45 and project equipment at 45-120, subject to confirmation. EXW, FOB, CIF and DAP are typical choices, while FCA, CFR, CPT, CIP and DDP are negotiable for specific orders.

Discuss Your Chain Project

Mark the 75mm pitch and the scraper interface on a copy of the dimensional view. Ever Power can discuss a like-for-like chain supply after reviewing the remaining connected conveyor details.

Verify A 75mm Paver Chain Replacement

RP Techniek BV (EVER-POWER Netherlands Branch)

Mail:

sales@netherlandsdrive.com

Professional production Speed Reducer, Worm Gearbox, Sprocket, Rack, Gear, Roller Chain, V-Belt Pulley, Motor, PTO Drive Shaft, Chain CC600, Taper Bushes Manufacturer and Supplier.

Blogs Updated