EP-CHG70 70mm Asphalt Paver Scraper Chain

Three 70mm-pitch scraper conveyor chain choices with different roller, pin and attachment geometry. Select EP-CHG70A, EP-CHG70B or EP-CHG70D from measured dimensions.

MOQ: flexible. Minimum order value USD 1,500; mixed orders and trial quantities available.

Overview

A repair enquiry that says only "70mm scraper chain" leaves out the information most likely to decide whether the new part will install. EP-CHG70 combines three published designs beneath one pitch family: EP-CHG70A, EP-CHG70B and EP-CHG70D. Their roller diameters are 22mm, 25mm and 30mm, respectively. The pin diameters, clear plate widths, scraper-related entries and vertical envelopes also change, so the three names should be treated as configuration identifiers rather than interchangeable stock codes.

Representative paver conveyor chain product photograph for the EP-CHG70 series; exact configuration must be checked against model dimensions
A paver conveyor chain shown as a construction reference; verify the different CHG70 scraper offsets before ordering.

This range is intended for the material-handling chain path in asphalt paving equipment. Buyers who are rebuilding a conveyor can use the comparison below to communicate the geometry that matters: the chain-to-sprocket interface, lateral width and relative position of the scraper connection. An exact equipment compatibility claim requires an original drawing or equivalent measured evidence.

Versions

3

Roller range

22-30 mm

Full Technical Specifications

Complete model dimensions

EP ModelPitch P (mm)Roller d1 (mm)Pin d2 (mm)Inner width b1 (mm)Scraper*Offset A3 (mm)Inner plate b2 (mm)Outer plate b3 (mm)Outer plate b4 (mm)Plate height H (mm)
EP-CHG70A702211.129856.566640
EP-CHG70B702512.728.0451.066630.0
EP-CHG70D703015.032.26-861.066640.0
70mm asphalt paver scraper chain engineering dimensional drawing for the EP-CHG70 family
Engineering profile showing the chain geometry and dimension symbols used to identify the listed EP family.

The Scraper source field includes 8, 4 and 6-8 across variants; it is shown exactly as printed and must be interpreted against the chain arrangement drawing.

70mm asphalt paver scraper chain specification table showing the published EP model dimensions
Series specification graphic for checking the tabulated technical values.

Related Chain Selection

If a paver service project involves additional conveyor chain types, use the existing industrial chain range.

Three Distinct Roller Envelopes

The smallest roller shown for this family belongs to EP-CHG70A at 22mm; EP-CHG70B uses 25mm, and EP-CHG70D uses 30mm. A single nominal pitch cannot explain such a spread in roller envelope. Compare each option with the tooth pocket of the existing drive sprocket and the clear passage through the guide. The correct roller must engage without forced seating or abnormal side contact.

The matching pin sizes are 11.1mm, 12.7mm and 15.0mm. Those values are not simply a sequence of quality grades. They identify distinct geometries that must be checked with the remaining dimensions. The width between inner plates is 29mm for A, 28.0mm for B and 32.2mm for D. A careful enquiry records all three values for the candidate model rather than describing the assembly only as narrow or heavy duty.

Attachment Offset Changes

Scraper geometry often determines whether an otherwise plausible chain can clear the conveyor floor and carry the connected hardware correctly. EP-CHG70A lists A3 at 56.5mm, EP-CHG70B at 51.0mm and EP-CHG70D at 61.0mm. Their plate heights are 40mm, 30.0mm and 40.0mm. Use the original dimension drawing to interpret these measurements, then confirm where the attached hardware sits on the actual conveyor.

The source also gives a Scraper entry of 8 for A, 4 for B and 6-8 for D. Because the column is not accompanied by a clear unit or engineering definition, retain these printed values as identifiers and request clarification for ordering. They should not be used to promise an exact attachment spacing without an approved assembly layout.

A 70mm chain pitch does not describe the scraper assembly. The roller, A3 offset and H dimension must be read as one configured set.

Understand The Chain Path

A paver can expose its scraper chain to packed material and intermittent loading. Observe how the links articulate around each sprocket, how the crosswise attachment is supported, and whether the two chain runs stay aligned. Unusual wear at one edge of a plate may indicate sideways loading from the conveyor arrangement rather than a defect in only the link being inspected.

During a retrofit, draw the route of the old chain and mark the drive, idlers, guides and scraper clearances. This gives the supplier useful context that a dimension table cannot capture. Any claim of suitability for a named paving machine must be validated against the machine configuration, because the provided series data is not an equipment cross-reference list.

EP-CHG70A technical specification card with dimensions and published parameters
EP-CHG70A individual model reference card. See the family table for every available code.
EP-CHG70D technical specification card with dimensions and published parameters
EP-CHG70D individual model reference card. See the family table for every available code.

Repair Scope And Spare Strategy

Specify whether the purchase is for one cut length, a pair of synchronized chain runs, replacement attachment components or a finished chain assembly. Not every customer needs the same supply scope. If the machine has operated with unmatched chain wear on the two sides, document that condition before selecting the replacement length and joining method.

A supply plan can include a controlled initial sample for fit checking where the project allows it. However, a successful hand fit is not a substitute for checking movement along the entire conveyor. Inspect the sprocket, chain guides and attachment contact faces during the same maintenance window so that a new chain is not immediately subjected to the old wear pattern.

Roller diameters of 22, 25 and 30mm demand careful selection of associated sprocket constructions; verify the tooth geometry and local mounting arrangement from the actual machine rather than assuming a catalogue match.

Evidence For Model Selection

Choose EP-CHG70A, B or D using the most discriminating measurements first: roller, pin, clear inner width, offset A3 and plate height. A code stamped on a worn part can help but should be checked against the dimensions, especially after machine modifications or previous repairs. Preserve photographs of both link faces and the attachment fitting.

If a replacement drawing must be prepared, identify the measured features that are original and the ones that are suspected wear. A complete review keeps confirmed catalogue values separate from customer-specific mounting requirements. That distinction reduces the chance that a drawing of a damaged scraper bracket becomes an incorrect production specification.

Additional Assembly View

In the 70mm family, the second view is useful for tracing scraper location across its three roller configurations. It does not override the individual EP-CHG70A, B or D data.

EP-CHG70 alternate chain assembly technical diagram
Additional engineering view for contextual checking of the scraper chain arrangement.

Measurement And RFQ Sequence

  1. Identify the installed roller size; 22mm, 25mm and 30mm divide the family into three clear candidates.
  2. Cross-check the pin size and the b1 inner gap for the selected candidate.
  3. Check A3 and H while the old attachment is still installed, then compare the values with the technical drawing.
  4. Record the source Scraper value and request clarification if attachment intervals affect the ordered assembly.
  5. Confirm the supply scope, including paired chains, attachment hardware, link count and joining preference.

Inspection Priorities

  • Compare wear marks near the material transfer point with marks at the return path.
  • Look for scraper attachments twisted relative to their adjoining link plates.
  • Inspect whether worn sprocket pockets are pushing rollers laterally.
  • Distinguish a mismatched replacement part from a conveyor alignment problem before changing a design.

Frequently Asked Questions

Can the three 70mm models share a replacement order without selection details?

They can be listed in one enquiry, but each line needs its exact model and quantity. Their roller diameters, pins, A3 positions and H heights differ; one common pitch does not authorize substitution.

What does the catalogue Scraper value mean for EP-CHG70D?

The published entry is 6-8. Its definition or unit is not sufficiently established in the supplied reference. If the ordered assembly depends on the number or spacing of scraper links, confirm that requirement from a drawing before production.

Which model has the 30mm roller?

EP-CHG70D is the listed member with d1 = 30mm. It also has d2 = 15.0mm, b1 = 32.2mm and A3 = 61.0mm; verify all of these rather than relying on the roller diameter alone.

Can low-volume repairs and mixed model purchases be quoted?

Yes, subject to commercial review. MOQ depends on the chain configuration and order value; appropriate buyers may request 1-5 samples. 1-2 pieces can be priced at a higher unit rate, and mixed orders generally target approximately USD 1,500 in total value.

What lead time and delivery terms should a repair planner allow?

Indicative production windows are 10-25 business days for standard items, 20-45 for custom assemblies and 45-120 for project equipment. Common terms include EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP or DDP can be considered after reviewing destination and shipment conditions.

Discuss Your Chain Project

A three-way comparison is most efficient when the roller and scraper dimensions are documented beside the original machine drawing. Ever Power welcomes a clear EP-CHG70A, EP-CHG70B and EP-CHG70D enquiry for replacement or planned maintenance.

Compare EP-CHG70 Variants With An Engineer

RP Techniek BV (EVER-POWER Netherlands Branch)

Mail:

sales@netherlandsdrive.com

Professional production Speed Reducer, Worm Gearbox, Sprocket, Rack, Gear, Roller Chain, V-Belt Pulley, Motor, PTO Drive Shaft, Chain CC600, Taper Bushes Manufacturer and Supplier.

Blogs Updated