MF385: 6.2 ml/rev, 160 bar, anticlockwise (CCW). Flexible MOQ by model and order value; 1–2 pcs can be considered at a higher unit price.
The MF385 model uses the same 6.2 ml/rev figure as MF375, but the catalogue gives a lower 160 bar maximum and 1500 rpm entry. Both run anticlockwise and use M18×1.5-6H threads. The rating difference matters for a replacement enquiry even when two units look alike in a thumbnail.
When an original unit has been changed before, the tractor badge can be misleading. Use the physical unit carrying MF and its drive-end photograph as the starting point.
No specific tractor serial ranges are established here for MF385. Use the parts manual and existing hardware to complete the application check.
| Reference / model | MF385 |
|---|---|
| Product type | Tractor Hydraulic Gear Pump |
| Original reference numbers | MF |
| Applicable tractor models | Confirm from original pump / equipment parts list |
| Manufacturer reference | MF385 |
| Nominal displacement | 6.2 ml/rev |
| Maximum pressure | 160 bar |
| Rotational speed | 1500 rpm |
| Controlled flow rate | 9.3 L/min |
| Feed hole / connection | M18×1.5-6H |
| Discharge hole / connection | M18×1.5-6H |
| Rotation | anticlockwise (CCW) |
For the stated 6.2 ml/rev pump, the hydraulic system remains the limiting context. Mechanical fit alone is not a test of working flow or acceptable drive load.
Within the comparison set, MF375 lists 6.2 ml/rev and 175 bar. That is a useful limit check for the MF385 hydraulic request, not permission to alter the tractor’s original pump rating.
The 9.3 L/min value is labeled controlled flow, not unrestricted outlet flow. Do not extrapolate it across all operating speeds.
The stated speed is 1500 rpm. Before commissioning, verify the engine accessory drive ratio and that normal operating conditions do not exceed this listing.
Even a correct cross-reference can fail if the drive turns the wrong way. The MF385 listing indicates counterclockwise, so trace the machine’s drive direction before use.
M18×1.5-6H and M18×1.5-6H are the recorded feed/discharge connection values. A mistaken swap between inlet and pressure ports should be resolved on the bench.
Drive rotationCCW
Displacement6.2 ml/rev
Connection checkM18×1.5-6H / M18×1.5-6H
One comparison point is Massey Ferguson MF375, where the record shows 6.2 ml/rev and 175 bar. The present MF385 specification (6.2 ml/rev, 160 bar) should be kept separate.
A supplier can review alternatives after the damaged part is identified by its original drawing or measurements.
Inspect the hydraulic reservoir and filter when changing to MF385. Recording the original failure symptoms and checking a blocked feed line may prevent an immediate second failure.
An incorrectly seated shaft coupling may damage both drive and pump even at light load.
For MF385, the most useful RFQ attachments are a shaft-end image, a drawing of the fastening pattern and the existing hose connector specification.
Replacement evaluations can proceed faster when photographs show all sides rather than only the top cover.
Only after confirming the actual port thread or bore, sealing system and clearance. Do not assume an adapter makes a mechanically wrong pump correct.
It is the maximum catalogue entry for this model, not proof that the tractor circuit or hoses may safely operate at that pressure.
Order quantities are set according to pump type and total order value. A small order of 1–2 pieces can be considered at a higher unit price; new customers may request 1–5 samples when the item is suitable. Mixed-model orders are available, normally with a combined order value of approximately USD 1,500.
Typical production schedules are 10–25 working days for standard items, 20–45 working days for customized components, and 45–120 working days for project equipment. Usual delivery terms are EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP and DDP can be discussed for specific shipments. Confirm the final schedule and terms with the quotation.
Third-party brand names and trademarks are used only for product identification and cross-reference. They remain the property of their respective owners; such references do not imply affiliation, sponsorship, authorization or endorsement.
Send the old pump reference, quantity, photos and interface measurements to our sales team.
sales@netherlandsdrive.com
| OEM |
|---|
Stainless steel gearboxes are widely used in industrial transmission fields due to their high strength and corrosion resistance. However, in actual use, stainless steel gearboxes may still malfunction due to improper design, installation, lubrication or maintenance....
In modern logistics automation systems, the CC600 Crate Conveyor Chain in Amsterdam plays a crucial role. With the continuous development of warehousing and sorting technologies, enterprises have increasingly higher requirements for the stability, efficiency and...
This article mainly explains and analyzes the structural design characteristics of the sprocket based on its role in the scraper conveyor, thereby leading to the necessity of researching the material and processing technology of the sprocket and the key technical...
