E6NN3K514PA: 15.0 ml/rev, 90 bar, anticlockwise (CCW). Flexible MOQ by model and order value; 1–2 pcs can be considered at a higher unit price.
E6NN3K514PA is the 15 ml/rev member of this Ford four-code group. Its 90 bar pressure listing and 3/4-16 UNF feed thread differ materially from the 225 bar E6NN3K514AB. This is a steering/hydraulic parts search reference: check whether the original has the same left-hand rotation and 9/16-18 UNF discharge thread.
Reference E6NN3K514PA appears with this Ford pump. On older tractor hydraulics, a casting number and a service part number may not be the same, so send both if visible.
No specific tractor serial ranges are established here for E6NN3K514PA. Use the parts manual and existing hardware to complete the application check.
| Reference / model | E6NN3K514PA |
|---|---|
| Product type | Tractor Hydraulic Gear Pump |
| Original reference numbers | E6NN3K514PA |
| Applicable tractor models | Confirm from original pump / equipment parts list |
| Manufacturer reference | Not provided |
| Nominal displacement | 15.0 ml/rev |
| Maximum pressure | 90 bar |
| Rotational speed | 500–3200 rpm |
| Controlled flow rate | 17.0 L/min |
| Feed hole / connection | 3/4-16 UNF |
| Discharge hole / connection | 9/16-18 UNF |
| Rotation | anticlockwise (CCW) |
The catalogue prints 15.0 ml/rev for this pump. When replacing it, avoid enlarging displacement on appearance alone: the input drive and relief protection were chosen around the original hydraulic demand.
Within the comparison set, E4NN3K514AB lists 14.0 ml/rev and 130 bar. That is a useful limit check for the E6NN3K514PA hydraulic request, not permission to alter the tractor’s original pump rating.
The flow-control annotation reads 17.0 L/min. Keep it with the original pump record rather than treating it as a measured output at 500–3200 rpm.
The stated speed is 500–3200 rpm. Before commissioning, verify the engine accessory drive ratio and that normal operating conditions do not exceed this listing.
The part Ford E4NN3K514AB is similar enough to deserve a check, not similar enough to presume interchangeability. Differences in CCW/CCW handedness or 14.0/15.0 displacement can affect both installation and operation.
A hydraulic pump replacement is only correct when dimensional and operational compatibility are both demonstrated.
For this part, the drive runs counterclockwise. Obtain an end-on shaft photo so the assembly orientation can be checked unambiguously.
Do not machine pipework from the illustration. The two connection callouts are feed 3/4-16 UNF and discharge 9/16-18 UNF; check the physical unit first.
Drive rotationCCW
Displacement15.0 ml/rev
Connection check3/4-16 UNF / 9/16-18 UNF
Confirm the tractor pump bracket is rigid and the shaft sits without axial force when E6NN3K514PA is installed. The original line arrangement should not load the aluminium body through unsupported fittings.
Document any adaptor or hose changes so future replacements are not ordered against outdated dimensions.
The enquiry for E6NN3K514PA should state expected order volume, required shipment term and any drawing that controls shaft projection. Mention whether this is a first sample or a repeat order.
For serial-sensitive machines, an equipment parts-list extract is especially helpful.
Look for a matching shaft profile, mounting flange and pressure-side connection; a parts number alone cannot settle every revision.
Not necessarily; controlled-flow information is separate from geometric displacement and actual delivery.
Order quantities are set according to pump type and total order value. A small order of 1–2 pieces can be considered at a higher unit price; new customers may request 1–5 samples when the item is suitable. Mixed-model orders are available, normally with a combined order value of approximately USD 1,500.
Typical production schedules are 10–25 working days for standard items, 20–45 working days for customized components, and 45–120 working days for project equipment. Usual delivery terms are EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP and DDP can be discussed for specific shipments. Confirm the final schedule and terms with the quotation.
Third-party brand names and trademarks are used only for product identification and cross-reference. They remain the property of their respective owners; such references do not imply affiliation, sponsorship, authorization or endorsement.
Send the old pump reference, quantity, photos and interface measurements to our sales team.
sales@netherlandsdrive.com
| OEM |
|---|
Stainless steel gearboxes are widely used in industrial transmission fields due to their high strength and corrosion resistance. However, in actual use, stainless steel gearboxes may still malfunction due to improper design, installation, lubrication or maintenance....
In modern logistics automation systems, the CC600 Crate Conveyor Chain in Amsterdam plays a crucial role. With the continuous development of warehousing and sorting technologies, enterprises have increasingly higher requirements for the stability, efficiency and...
This article mainly explains and analyzes the structural design characteristics of the sprocket based on its role in the scraper conveyor, thereby leading to the necessity of researching the material and processing technology of the sprocket and the key technical...
