YH4.60.37 (16T) — 16/10 ml/rev; max. 20 MPa; 900–3000 rpm; clockwise rotation. MOQ is flexible by pump type and order value, with 1–2 pcs available at higher unit prices.
20 MPa • 900–3000 rpm • Clockwise rotation
YH4.60.37 (16T) is a harvester hydraulic gear pump offered by Ever Power Netherlands Branch. Nominal displacement is 16/10 ml/rev, the listed pressure is 20 MPa, and the speed reference is 900–3000 rpm.
A hydraulic gear pump on a combine harvester must keep up with changing engine speed and variable actuator demand. Pressure rating, shaft drive, rotation and installed envelope all matter; a matching nominal flow figure is not enough.
This 16-tooth reference specifies a 900–3000 rpm operating range, useful where the hydraulic pump runs at varying engine speeds. It cannot be selected solely from displacement.
The listed pump hand is clockwise; check the rotation convention shown on the existing installation.
The 16/10 ml/rev figures identify a two-volume arrangement; circuit connections and functions must be confirmed.
Hydraulic oil cleanliness, heat and harvest dust influence long-term operation.
The 16T drive reference differs from YH4.60.37a (11T). Compare tooth profile, shaft engagement, bolt centres and port orientation on the removed unit.
Confirm shaft/tooth count, coupling engagement and rotation.
Compare the 16/10 ml/rev duty against machine flow demand.
Check relief pressure, clean oil supply and port routing.
Compare nearby pump references by actual hydraulic figures first. Connection geometry and pump drive arrangement still need to be matched independently.
| Model | Displacement | Pressure | Speed | Rotation |
|---|---|---|---|---|
| YH4.60.37a (11T) | 16/10 ml/rev | 20 MPa | 3000 rpm | Clockwise |
| YH4.60.37 (16T) | 16/10 ml/rev | 20 MPa | 900–3000 rpm | Clockwise |
| Product reference | YH4.60.37 (16T) |
|---|---|
| Pump application | Harvester Hydraulic Gear Pump |
| Nominal displacement | 16/10 ml/rev |
| Listed maximum pressure | 20 MPa |
| Speed reference | 900–3000 rpm |
| Rotation direction | Clockwise |
| Inlet / suction connection | Not specified |
| Outlet / discharge connection | Not specified |
| Typical application | combine harvesters and agricultural harvesting equipment |
| Mounting/shaft drawing | Confirm dimensions and drawing availability for the ordered configuration |
| Supplier | Ever Power Netherlands Branch |
Flow and pressure must be evaluated with the machine’s pump drive, circuit relief setting and duty cycle. The listed maximum is not a blanket continuous-duty guarantee.
At the listed 16/10 ml/rev displacement and 20 MPa maximum pressure, the choice between 11T and 16T still depends on the drive connection. These two references should not be treated as dimensionally interchangeable without drawings.
For a harvester already in service, record the current pump number, tooth count, shaft engagement depth, mounting flange, inlet and outlet positions, and the rotation observed in the machine’s service information.
Secure the drive coupling, identify the tooth count and check the stated clockwise direction against the machine diagram before running the pump.
Use the hydraulic oil grade specified by the harvester manufacturer. Protect open ports during installation and inspect suction cleanliness and filter condition.
Prime according to the machine instructions, inspect for leaks and abnormal noise, then check operation under light load before returning to harvest duty.
Use the original pump marking for identification, then compare the shaft, flange, port layout, rotation and hydraulic duty. OEM reference numbers help start a cross-check; they do not by themselves establish one-to-one interchangeability.
| Reference to compare | YH4.60.37 (16T) |
|---|---|
| Hydraulic figures | 16/10 ml/rev; 20 MPa; 900–3000 rpm |
| Rotation check | Clockwise |
| Physical check | Drive end, flange, ports, clearance and mounting hole centres |
| Documents for confirmation | Nameplate or OEM reference, photos, dimensioned drawing where available |
Both have 16/10 ml/rev and a listed 20 MPa figure. Their 11T and 16T identification differs, and the 16T reference lists 900–3000 rpm while the 11T reference lists 3000 rpm. Compare the drive interface before substitution.
Clockwise for both references. Confirm the viewing convention and driven shaft arrangement before assembly.
Fit must be checked from the machine model, original pump reference, shaft/tooth count, flange and ports. A general application label is not a fitment approval.
Submit a drawing or clear measurements with your order quantity so the available configuration can be evaluated.
Minimum order quantity (MOQ) is assessed by pump type, specification and total order value. Where production conditions allow, orders of just 1–2 units can be quoted, although the unit price will usually be higher than for a batch order.
New customers may request 1–5 samples when suitable. Availability and sample pricing are confirmed for the selected model.
Different hydraulic pump models may be combined in one order; the target combined order value is approximately USD 1,500.
Standard parts: 10–25 working days. Customized assemblies: 20–45 working days. Project equipment: 45–120 working days.
Trade terms: EXW, FOB, CIF and DAP are normally available. FCA, CFR, CPT, CIP and DDP can be discussed according to the destination and shipment requirements. The agreed lead time and Incoterm will be stated in the formal quotation.
For another pump reference within this application, compare YH4.60.37a (11T). Confirm the replacement interfaces rather than ordering from displacement figures alone.
For YH4.60.37 (16T), send the required quantity, the equipment model, an existing part number, shaft and port photos, and any available dimension drawing. Contact Ever Power Netherlands Branch at sales@netherlandsdrive.com.
Stainless steel gearboxes are widely used in industrial transmission fields due to their high strength and corrosion resistance. However, in actual use, stainless steel gearboxes may still malfunction due to improper design, installation, lubrication or maintenance....
In modern logistics automation systems, the CC600 Crate Conveyor Chain in Amsterdam plays a crucial role. With the continuous development of warehousing and sorting technologies, enterprises have increasingly higher requirements for the stability, efficiency and...
This article mainly explains and analyzes the structural design characteristics of the sprocket based on its role in the scraper conveyor, thereby leading to the necessity of researching the material and processing technology of the sprocket and the key technical...
