Overview
For an 80mm-pitch asphalt paver conveyor, a nominal pitch match answers only one part of the selection question. The EP-CHG80 family contains five variants whose roller diameters run from 22mm to 36mm. Pin size, inner width, plate parameters, scraper offset and vertical height also differ. A buyer who specifies “80mm chain” without a complete dimensional fingerprint risks receiving a part that will not sit correctly on the installed sprocket or connect to the existing scraper assembly.

EP-CHG80A, EP-CHG80B, EP-CHG80C, EP-CHG80F and EP-CHG80G are grouped on one page because they share a meaningful family relationship, not because they can replace one another. The comparison matrix allows maintenance planners to screen available designs and decide which measurements need physical confirmation before a quotation is prepared.
Available versions
5
Rollers
22-36 mm
Full Technical Specifications
Complete model dimensions
| EP Model | Pitch P (mm) | Roller d1 (mm) | Pin d2 (mm) | Inner width b1 (mm) | Scraper* | Offset A3 (mm) | Inner plate b2 (mm) | Outer plate b3 (mm) | Outer plate b4 (mm) | Plate height H (mm) |
|---|---|---|---|---|---|---|---|---|---|---|
| EP-CHG80A | 80 | 22 | 12.7 | 27 | 4 | 49.6 | 6 | 6 | 6 | 38.1 |
| EP-CHG80B | 80 | 26 | 18.0 | 36 | 4 | 56.5 | 8 | 6 | 8 | 45 |
| EP-CHG80C | 80 | 27.94 | 15.9 | 33.8 | 4-6 | 56.5 | 6 | 8 | 8 | 45.0 |
| EP-CHG80F | 80 | 36 | 18.0 | 35.0 | 6 | 63.0 | 8 | 8 | 8 | 45.0 |
| EP-CHG80G | 80 | 24 | 15.9 | 26 | 4 | 51.0 | 8 | 8 | 8 | 38 |
The Scraper values vary between the five 80mm entries; their engineering meaning and assembly application must be confirmed from the actual ordered layout.
Related Chain Selection
A purchasing schedule spanning multiple scraper conveyor models can start at the industrial chain range.
Five Roller Families
The five EP-CHG80 versions are easiest to separate first by roller diameter. EP-CHG80A uses 22mm, EP-CHG80G uses 24mm, EP-CHG80B uses 26mm, EP-CHG80C uses 27.94mm and EP-CHG80F uses 36mm. The progression is not a defined load class or performance ranking. It is the published geometry of five different parts. Always use roller size to narrow candidate models, then check pin and plate values before drawing a conclusion.
A second screening dimension is d2. Values include 12.7mm for EP-CHG80A, 15.9mm for EP-CHG80C and EP-CHG80G, and 18.0mm for EP-CHG80B and EP-CHG80F. Two parts can share a pin diameter without sharing roller size or offset. This is why a step-by-step selection table provides more value than a list of model names and generic claims about durability.
Identify Each Model Precisely
EP-CHG80A is the 22mm-roller configuration with b1 = 27mm, A3 = 49.6mm and H = 38.1mm. EP-CHG80G uses a 24mm roller, b1 = 26mm and A3 = 51.0mm, with H listed at 38mm. EP-CHG80B introduces a 26mm roller and the widest inner-plate gap in this family at 36mm. Each has its own b2/b3/b4 pattern, so apparent similarity in the side view cannot replace the table.
EP-CHG80C is the entry with a precisely stated 27.94mm roller diameter and a 33.8mm inner width. EP-CHG80F has the largest listed roller at 36mm and A3 of 63.0mm. Both reach H = 45.0mm but have different pins, plate data and scraper entries. If the supplied machine drawing requires one specific variant, preserve that full designation on the purchase order.
Five models share P = 80mm, but not the same rollers, pin diameters, inner widths or scraper locations. Select from the full technical row.
Interpreting Scraper Geometry
The A3 dimension describes the relative location of the scraper feature identified on the drawing. Across the family it is 49.6, 56.5, 56.5, 63.0 and 51.0mm for the A, B, C, F and G configurations, respectively. Check it against the existing assembly at the installed position. Do not substitute one value merely because the chain can be stretched between the same sprockets.
The separate Scraper column has entries 4, 4, 4-6, 6 and 4. The meaning of the published category is not sufficiently defined to create a finished attachment pitch or supply count without confirmation. A configured scraper assembly should therefore be specified by an approved drawing or a mutually verified sample.
Machine Integration Review
Material-conveyor chains operate inside the physical constraints set by a machine frame, guides, sprockets and scraper bars. Assess the travel route through both the loaded and empty return sections. In the workshop, check the effective attachment envelope at the closest point to fixed metal and measure whether both chain runs remain parallel under slow rotation.
For a replacement project, note any changes made to the sprockets or guides since the machine was built. An earlier component substitution can make an apparently original code unreliable. The technically safe procedure is to reconcile installed measurements with the documented series row, then approve the actual configuration rather than asserting broad machine compatibility.
Five distinct roller geometries may call for different checks of sprocket constructions; verify the tooth geometry and local mounting arrangement from the actual machine rather than assuming a catalogue match.
Quality And Maintenance Focus
The service team should monitor roller freedom, pin-end condition, link plate deformation, tooth-pocket wear and scraper fastener security. Inspect the location and direction of damage: abrasion concentrated on one side can point toward an alignment issue, whereas repeated damage at a tight turn may suggest a clearance problem.
A new chain is not a cure for a badly worn or misaligned sprocket system. Assess the driving component and the attachment mounting points during the same shutdown. No unsupported working load, hardness specification or replacement interval is attributed to the EP-CHG80 family; these values require a separate engineering source or confirmed order drawing.
Additional Assembly View
For the five EP-CHG80 variations, this alternate drawing highlights a further chain arrangement. Trace the connection geometry here, then use the five-model matrix to decide the exact assembly specification.
Measurement And RFQ Sequence
- Measure 80mm pitch across several links and confirm that this is the intended sprocket geometry.
- Use the roller diameter to narrow the field among the five documented candidates.
- Measure d2 and b1, taking particular care to distinguish B and F configurations.
- Check A3, b2, b3, b4, H and the printed Scraper entry against the actual attachment arrangement.
- Identify the exact requested variant, chain run and required link count on the RFQ, leaving no default substitution implied.
Inspection Priorities
- Confirm that rollers of significantly different diameters have not been mixed during previous repairs.
- Examine whether the widest plate configuration has enough room through its guide channel.
- Inspect scraper bars for looseness that might mimic a wrong A3 offset.
- Document sprocket tooth condition before evaluating a replacement sample.
Frequently Asked Questions
Does an 80mm pitch make all EP-CHG80 models interchangeable?
No. The published family includes roller diameters from 22mm to 36mm, different pin sizes, inner widths and attachment offsets. The exact EP model must be selected against the fitted machine geometry.
Which variant lists the largest roller diameter?
EP-CHG80F is specified with a 36mm roller, 18.0mm pin, 35.0mm inner width, 63.0mm A3 and 45.0mm H. Those values identify its geometry; they do not certify a particular working load.
What should I provide when the old model code is unreadable?
Send pin-center pitch measurements, roller and pin diameters, clear inner plate width, A3/H measurements, sprocket photographs, attachment views and a summary of the required assembly length.
Are a few pieces or combinations of EP-CHG80 variants allowed?
Trial requests may be assessed for 1-5 pieces where appropriate. A 1-2-piece order is possible in some circumstances but normally has a higher unit price. Mixing different EP chain models is acceptable toward an approximate USD 1,500 minimum order value.
What manufacturing times and Incoterms may be quoted?
Standard parts are commonly scheduled for 10-25 working days, customized components for 20-45 and project equipment for 45-120. EXW, FOB, CIF and DAP are standard discussion options; FCA, CFR, CPT, CIP and DDP can be negotiated when the shipment scope is defined.
Discuss Your Chain Project
Please identify the target EP-CHG80 letter and attach the roller, pin, b1 and A3 readings. Ever Power can use this configuration record to discuss the complete supply scope of the required paver conveyor chain.
Identify The Correct EP-CHG80 Chain Variant
