Deutz-Fahr CBN-E314R: tractor hydraulic gear pump replacement reference
CBN-E314R is a 14 ml/rev clockwise Deutz-Fahr reference. Its 16 MPa and 2500 rpm entries are given in different units from the Ford bar-rated group; preserve those labels during comparison. The 18 mm feed and 14 mm discharge openings are a practical first screen for mating hardware.
Model identity and its limits
The main identification for this entry is CBN-E314R. The accompanying reference list is CBN-E314R; compare the reference stamped on the removed body rather than relying on a generic seller photo.
No specific tractor serial ranges are established here for CBN-E314R. Use the parts manual and existing hardware to complete the application check.
Technical specifications
| Reference / model | CBN-E314R |
|---|---|
| Product type | Tractor Hydraulic Gear Pump |
| Original reference numbers | CBN-E314R |
| Applicable tractor models | Confirm from original pump / equipment parts list |
| Manufacturer reference | Not provided |
| Nominal displacement | 14 ml/rev |
| Maximum pressure | 16 MPa |
| Rotational speed | 2500 rpm |
| Controlled flow rate | Not stated |
| Feed hole / connection | Ø18 |
| Discharge hole / connection | Ø14 |
| Rotation | clockwise (CW) |
Connection geometry and handedness
Checking rotation for CBN-E314R requires a known viewpoint. Record whether the shaft was observed from the coupling face, as the listing gives clockwise.
A parts drawing should confirm the supply-side opening (Ø18) and the pressure-side opening (Ø14) with their centerline positions.
Drive rotationCW
Displacement14 ml/rev
Connection checkØ18 / Ø14
The mistaken-substitution risk
As a sanity check, compare this entry with Deutz-Fahr C60.58.001.0. A near-identical picture is weaker evidence than distinct OEM numbers, connection shapes and the stated CW rotation.
The complete assembly should be assessed, including drive-end engagement and the supply port.
Correcting a size mismatch
At 14 ml/rev, CBN-E314R sits in a particular displacement range of the Deutz-Fahr pump list. Confirm the circuit’s demand before judging capacity, because an equal-looking body can contain different gear widths.
Within the comparison set, C60.58.001.0 lists 14 ml/rev and 16 MPa. That is a useful limit check for the CBN-E314R hydraulic request, not permission to alter the tractor’s original pump rating.
No controlled-flow rate is specified for this item; please include duty conditions if that value is required in the RFQ.
The stated speed is 2500 rpm. Before commissioning, verify the engine accessory drive ratio and that normal operating conditions do not exceed this listing.
Commissioning considerations
Before the first start, rotate the drive in the correct direction by the approved maintenance procedure and verify CBN-E314R receives oil. Run unloaded initially and monitor for abnormal sound or leakage.
Before releasing the tractor to service, inspect both connections for seepage under the manufacturer’s safe checking procedure.
A clear hydraulic pump RFQ
If replacing a failed Deutz-Fahr unit, share its stamped identifier, gearbox or engine-side drive photo and port measurements. The listed 16 MPa pressure is not a substitute for the machine’s actual relief setting.
State whether you need one qualification unit before authorizing a production lot.
Two questions worth resolving
How can a workshop identify CBN-E314R correctly?
Compare the original identification marking with CBN-E314R and measure the drive connection before selecting a replacement.
What does the 16 MPa pressure value represent?
It is the maximum catalogue entry for this model, not proof that the tractor circuit or hoses may safely operate at that pressure.
Ordering, samples and shipping terms
Order quantities are set according to pump type and total order value. A small order of 1–2 pieces can be considered at a higher unit price; new customers may request 1–5 samples when the item is suitable. Mixed-model orders are available, normally with a combined order value of approximately USD 1,500.
Typical production schedules are 10–25 working days for standard items, 20–45 working days for customized components, and 45–120 working days for project equipment. Usual delivery terms are EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP and DDP can be discussed for specific shipments. Confirm the final schedule and terms with the quotation.
Third-party brand names and trademarks are used only for product identification and cross-reference. They remain the property of their respective owners; such references do not imply affiliation, sponsorship, authorization or endorsement.
Request a quotation for this pump
Send the old pump reference, quantity, photos and interface measurements to our sales team.
sales@netherlandsdrive.com