Deutz-Fahr C60.58.001.0: tractor hydraulic gear pump replacement reference
C60.58.001.0 has the same nominal displacement and listed pressure as CBN-E314R but runs anticlockwise, whereas CBN-E314R runs clockwise. That opposite rotation is an immediate selection blocker. The shared 18 mm/14 mm openings do not establish full mechanical interchangeability.
Identification before quotation
Before treating C60.58.001.0 as an interchangeable spare, compare the inlet-side and discharge-side hardware. Different bodies can share a family reference without sharing every connection.
No specific tractor serial ranges are established here for C60.58.001.0. Use the parts manual and existing hardware to complete the application check.
Technical specifications
| Reference / model | C60.58.001.0 |
|---|---|
| Product type | Tractor Hydraulic Gear Pump |
| Original reference numbers | C60.58.001.0 |
| Applicable tractor models | Confirm from original pump / equipment parts list |
| Manufacturer reference | Not provided |
| Nominal displacement | 14 ml/rev |
| Maximum pressure | 16 MPa |
| Rotational speed | 2500 rpm |
| Controlled flow rate | Not stated |
| Feed hole / connection | Ø18 |
| Discharge hole / connection | Ø14 |
| Rotation | anticlockwise (CCW) |
Interpreting the pressure listing
The nominal size of C60.58.001.0 is 14 ml/rev. The user should confirm both required pressure and expected duty cycle; a part that spins and bolts on can still perform poorly if incorrectly sized.
Within the comparison set, CBN-E314R lists 14 ml/rev and 16 MPa. That is a useful limit check for the C60.58.001.0 hydraulic request, not permission to alter the tractor’s original pump rating.
The omission of a controlled-flow line should be treated as unknown information, not as evidence that this pump has no flow control.
The stated speed is 2500 rpm. Before commissioning, verify the engine accessory drive ratio and that normal operating conditions do not exceed this listing.
Connection geometry and handedness
The selection should rule out the opposite drive hand at the outset: C60.58.001.0 is CCW. Do not rotate a directional unit backwards to make its fittings line up.
Installation hardware must suit Ø18 on the supply side and Ø14 on the discharge side. A port-size match alone does not prove the mount will align.
Drive rotationCCW
Displacement14 ml/rev
Connection checkØ18 / Ø14
Before choosing the nearest-looking pump
As a sanity check, compare this entry with Deutz-Fahr CBN-E314R. A near-identical picture is weaker evidence than distinct OEM numbers, connection shapes and the stated CCW rotation.
A hydraulic pump replacement is only correct when dimensional and operational compatibility are both demonstrated.
Inspect the hydraulic drive
An installation review should include oil grade, tank venting and relief valve condition for C60.58.001.0. If the previous pump failed from starvation or high pressure, replacement alone will not remove the cause.
Circuit operating flow remains unquantified in this row, so a controlled functional check is needed once the pump is installed.
Information to put on the purchase enquiry
A useful request specifies C60.58.001.0 by OEM reference and includes the hydraulic system’s working duty. Supply the exact rotation convention and two views of the pump body.
Ask for an outline drawing when a tight installation envelope leaves little room for adapters.
What buyers ask about this model
Which information distinguishes C60.58.001.0 from adjacent entries?
The OEM number, CCW handedness and the listed feed/discharge values should be checked together with the flange.
What does 14 ml/rev mean for flow?
It describes displacement per revolution, not a guaranteed service flow; compare actual shaft rpm and pump efficiency.
Ordering, samples and shipping terms
Order quantities are set according to pump type and total order value. A small order of 1–2 pieces can be considered at a higher unit price; new customers may request 1–5 samples when the item is suitable. Mixed-model orders are available, normally with a combined order value of approximately USD 1,500.
Typical production schedules are 10–25 working days for standard items, 20–45 working days for customized components, and 45–120 working days for project equipment. Usual delivery terms are EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP and DDP can be discussed for specific shipments. Confirm the final schedule and terms with the quotation.
Third-party brand names and trademarks are used only for product identification and cross-reference. They remain the property of their respective owners; such references do not imply affiliation, sponsorship, authorization or endorsement.
Request a quotation for this pump
Send the old pump reference, quantity, photos and interface measurements to our sales team.
sales@netherlandsdrive.com