Deutz 19 + 13 cc tandem: tandem hydraulic gear pump replacement reference
This tandem Deutz assembly is specified as 19+13 ml/rev with pressure values listed separately as 250/200 bar. Do not treat either value as a universal limit for both stages. Identify which section supplies each circuit, inspect the interstage body orientation and verify the corresponding outlet before specifying the replacement.
Trace the correct reference
An enquiry for 19 + 13 cc tandem should include the complete identifier, not a truncated family number. The corresponding Deutz hydraulic component must also be checked against the machine’s mounting arrangement.
No specific tractor serial ranges are established here for 19 + 13 cc tandem. Use the parts manual and existing hardware to complete the application check.
Technical specifications
| Reference / model | 19 + 13 cc tandem |
|---|---|
| Product type | Tandem Hydraulic Gear Pump |
| Original reference numbers | DEUTZ |
| Applicable tractor models | Confirm from original pump / equipment parts list |
| Manufacturer reference | 19CC+13CC |
| Nominal displacement | 19/13 ml/rev |
| Maximum pressure | 250/200 bar |
| Rotational speed | 3000 rpm |
| Controlled flow rate | Not stated |
| Feed hole / connection | Ø20 |
| Discharge hole / connection | Ø15 |
| Rotation | anticlockwise (CCW) |
A useful alternative reference check
As a sanity check, compare this entry with Deutz 18 + 12 cc tandem. A near-identical picture is weaker evidence than distinct OEM numbers, connection shapes and the stated CCW rotation.
The complete assembly should be assessed, including drive-end engagement and the supply port.
How to compare pump sizes
The two working volumes for 19 + 13 cc tandem are listed independently as 19/13 ml/rev; each section can see different loads in the tractor system. Keep this distinction when describing the circuit to an engineer.
Within the comparison set, 18 + 12 cc tandem lists 18/12 ml/rev and 250 bar. That is a useful limit check for the 19 + 13 cc tandem hydraulic request, not permission to alter the tractor’s original pump rating.
Flow-control behavior is not defined by this parts entry. Confirm the tractor valve and circuit characteristics independently.
The stated speed is 3000 rpm. Before commissioning, verify the engine accessory drive ratio and that normal operating conditions do not exceed this listing.
Service checks worth recording
Before removing 19 + 13 cc tandem, mark each hydraulic hose with its original position and note how the drive coupling engages. Then check the condition of the drive teeth, mounting gasket and fasteners on the old unit.
A final leak check should be made only after the equipment has been secured and depressurization procedures followed.
Connection geometry and handedness
19 + 13 cc tandem is marked counterclockwise rotation. Identify the shaft end before interpreting the arrow and compare the actual pump drive direction with the equipment drawing.
Size the mating fittings around the source entries — Ø20 for feed and Ø15 for discharge — not around a photograph’s scale.
Drive rotationCCW
Displacement19/13 ml/rev
Connection checkØ20 / Ø15
How to specify this replacement
Send model 19 + 13 cc tandem, the quantity and one legible photo of the part mark. For interface review, add the drive-shaft profile, bolt spacing and a drawing of the port locations.
Where the pump feeds two circuits, label each section and its pressure-line attachment.
What buyers ask about this model
Why ask for the original pump image?
It reveals drive and connector details that the part reference DEUTZ alone may not identify.
What does the 250/200 bar pressure value represent?
It is the maximum catalogue entry for this model, not proof that the tractor circuit or hoses may safely operate at that pressure.
Ordering, samples and shipping terms
Order quantities are set according to pump type and total order value. A small order of 1–2 pieces can be considered at a higher unit price; new customers may request 1–5 samples when the item is suitable. Mixed-model orders are available, normally with a combined order value of approximately USD 1,500.
Typical production schedules are 10–25 working days for standard items, 20–45 working days for customized components, and 45–120 working days for project equipment. Usual delivery terms are EXW, FOB, CIF and DAP. FCA, CFR, CPT, CIP and DDP can be discussed for specific shipments. Confirm the final schedule and terms with the quotation.
Third-party brand names and trademarks are used only for product identification and cross-reference. They remain the property of their respective owners; such references do not imply affiliation, sponsorship, authorization or endorsement.
Request a quotation for this pump
Send the old pump reference, quantity, photos and interface measurements to our sales team.
sales@netherlandsdrive.com